电动门如何正确的使用与检修 电动门是我们生活中很常见的一种工具,在很多地方都能够应用到,但是,对于电动门的正确的使用与检修,大家并不是很了解,那么,今天的内容中小编就带领大家一起来了解一下. 电动门要确定传达室内控制盒的位置,即操纵伸缩门开关的装置位置;将220V电源引到控制盒的位置下端,要求最好是再带1根接地线,粗细规格为1.37,而且有漏电保护装置,并采用PVC暗敷;预留￠32mm PVC管道,从控制盒的位置下端往下至地平面以下,穿墙往外,至轨道大致位置地平面下0.1-0.15米处,供以后伸缩门室外线路入室;按照上表得出门洞长度,砌门洞时洞宽内净空不小于0.75-0.8米,高度内净尺寸普通门不小于门高+0.25米,豪华门不小于门高+0.1米. 电动门门洞末端里侧中上端留宽0.4米,高0.6米检修孔,有条件的可将门洞总长度再加长0.2-0.3米,这样可将检修孔改成一扇小门,方便日后检修维护伸缩门电气线路;在铺设轨道前除留下约0.8-0.9米宽外,先做好两边的地面;2-3日(冬天5-7日)后,再在铺设轨道的同时,土建配合做好轨道处的地面,注意铺设轨道期间,路面禁止通行,以免压弯轨道;安装伸缩门,接好线路,调试开关控制盒. 想要电动门正常的工作,那么在安装电动门时就地变电阻柜 精密铸造 中频电炉设备 保定断桥铝门窗 保定养老院 镜子批发 启闭机要格外的细心,正所谓,建一座大楼,首先就要打好地基,电动门的安装也是这样,做好电动门的安装工作,才能够确保电动门在日后能够正常的工作.
How to use and maintain electric doors correctly is a common tool in our daily life, which can be applied in many places. However, for the correct use and maintenance of electric doors, everyone is not very familiar with it. So, today's content, I will lead everyone to understand The electric door needs to determine the position of the indoor control box, that is, the position of the device that operates the telescopic door switch; Lead the 220V power supply to the lower end of the control box, preferably with an additional grounding wire, with a thickness specification of 1.37 and a leakage protection device, and use PVC concealed laying; Reserve a 32mm PVC pipeline from the lower end of the control box to below the ground level, through the wall and outward, to approximately 0.1-0.15 meters below the ground level of the track, for future expansion door outdoor lines to enter the room; According to the length of the door opening shown in the table above, when building the door opening, the width and clearance inside the opening should not be less than 0.75-0.8 meters, and the height and clearance inside the opening should not be less than the door height+0.25 meters for ordinary doors and+0.1 meters for luxury doors. A 0.4 meter wide and 0.6 meter high access hole should be left at the middle and upper ends of the inner side of the electric door opening. If conditions permit, the total length of the door opening can be extended by an additional 0.2-0.3 meters, which can turn the access hole into a small door for future maintenance and repair of the electrical circuit of the expansion door; Before laying the track, except for leaving a width of approximately 0.8 to 0.9 meters, prepare the ground on both sides first; After the 2nd to 3rd day (5th to 7th day in winter), while laying the track, civil engineering should cooperate to prepare the ground at the track. During the laying of the track, traffic on the road surface should be prohibited to avoid bending the track; Install the expansion door, connect the wiring, and debug the switch control box To ensure the normal operation of electric doors, it is necessary to be particularly careful when installing them. As the saying goes, to build a building, the first step is to lay a solid foundation, and the installation of electric doors is the same. Only by doing a good job in the installation of electric doors can we ensure their normal operation in the future
